composite cement CEM II/C-M and Composite cement CEM VI

BS EN 197-5:2021 pdf free.Cement Part 5: Portland-composite cement CEM II/C-M and Composite cement CEM VI.
Cements covered by this document shall be designated by at least the notation of the cement type as specified in Table 1 and the Figures 32,5, 42,5 or 52.5 indicating the strength class. In order to indicate the early strength class the letter L. N or R shall be added as appropriate.
When in the same factory a manufacturer produces different cements complying with the same standard designation, these cements receive an additional identification in the form of a number or of two lower case letters, between brackets, in order to distinguish these cements from each other. For the numbering system, this number should be 1 for the second certified cement, 2 for the next, and so on. For the lettering system, the letters shall be chosen in such a way as to avoid confusion.
Low heat cement in accordance with 7.2.3 of EN 197-1:2011 shall be additionally designated by the notation LH,
Portland-composite cement CEM ll/C-M containing in total a quantity of silicious fly ash (V) of between 16 % and 44 % by mass and a quantity of limestone (LL) of between 6 % and 20 % by mass and of strength class 32,5 with high early strength and a low heat of hydration is designated by:
Portland-composite cement EN 197-5 – CEM ll/C-M (V-LL) 32,5 R
Portland-composite cement CEM ll/C-M containing in total a quantity of granulated blast furnace slag (S) of between 6 % and 44 % by mass and a quantity of silicious fly ash (V) of between 6 % and 44 % by mass and of strength class 42,5 with ordinary early strength and a low heat of hydration is designated by:
Portland-composite cement EN 197-5 – CEM IJ/C-M (S-V) 42,5 N — LH
Composite cement CEM VI containing in total a quantity of granulated blast furnace slag (S) of between 31 % and 59% by mass and limestone (L) of between 6% and 20% by mass and of strength class 32,5 with high early strength is designated by:
Composite cement EN 197-5 — CEM VI (S-I) 32,5 R
Composite cement CEM VI containing in total a quantity of granulated blast furnace slag (S) of between 31 % and 59 % by mass and natural pozzolana (P) of between 6% and 20 % by mass and of strength class 42,5 with low early strength is designated by:
Corn posite cement EN 197-5 – CEM VI (S-P) 42,5 1
7 Conformity criteria
For cements covered by this document the conformity criteria specified in Table 2 and in Clause 9 of
EN 197-1:2011 shall apply. In particular, conformity criteria specified for “all cements” in
EN 197-1:2011 shall also apply for cement covered by this document.
The conformity of cements covered by this document should be demonstrated by:
— factory production control, including product assessment, in accordance with Clause 4 of
EN 197-2:2020;
— assessment of the performance of the cement in accordance with 5.1 of EN 197-2:2020;
— initial inspection of the manufacturing plant and of factory production control in accordance with 5.2 of EN 197-2:2020;
— continuing surveillance, assessment and evaluation of factory production control in accordance with 5.3 of EN 197-2:2020;
— audit-testing of samples taken at the factory/depot in accordance with 5.4 of EN 197-2:2020. Information concerning reports is given in 5.5 of EN 197-2:2020. Actions to be taken in the event of non-conformity are specified in 5.6 of EN 197-2:2020.
8 Attestation of conformity
For the attestation of conformity of cements covered by this document the procedure specified in Clause 6 of EN 197-2:2020 shall apply. When compliance with the conditions of this document is achieved, a certificate of conformity should be issued. The certificate shall include:
— name, address and identification number of the certification body;
— standard designation of the cement;
— name and address of the manufacturer or distributor and place of production;
— provisions to which the product conforms (ie. this EN 197-5);
— conditions of validity of the certificate, where applicable;
一 the number of the certificate;
— name of, and position held by, the person empowered to sign the certificate.
NOTE The terms “assessment and verification of constancy of performance (AVCP) and certificate of constancy of performance are used in EN 197-2:2020 following the Commission Delegated Regulation (EU) No 568/2014. The use of these terms is not possible for cements covered by this document which is not a harmonized European standard.
The procedures to be used to evaluate the representativeness and the accuracy of the 28-day strength test results are described in the normative Annex A of EN 197-2:2020.
Information concerning the procedure for certification of constancy of performance of cement is given in the informative Annex B of EN 197-2:2020.
9 Marking and labelling
The choice of cement covered by this document, particularly as regards type and strength class for different applications and exposure classes, as well as the marking and labelling shall follow the appropriate standards and/or regulations valid in the place of use.
On the packaging, or for bulk product on the delivery documents, at least the following information shall be given:
— standard designation of the cement;
— manufacturer or distributor (name and address, plant);
— weight (nominal weight of bags or net weight of bulk cement);
— name or symbol of the product certification body.
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 197-1:2011, Cement — Part 1: Composition, specflcations and conformity criteria for common cements
EN 197-2:2020, Cement — Part 2: Assessment and verification of constancy of performance
EN 196-2, Method of testing cement — Part 2: Chemical analysis of cement
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 197-1:2011 apply. ISO and TEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp 4 Constituents and composition
Constituents of cement covered by this document shall fulfil the requirements specified in Clause 5 of
EN 197-1:2011.
However, the following requirement for limestone (L, LL) replacing 5.2.6 a) of EN 197-1:2011 shall apply:
The calcium carbonate (CaCO3) content calculated from the calcium oxide content shall be at least 40 % by mass and the sum of calcium carbonate and magnesium carbonate (CaCO3 and MgCO3) content calculated from the calcium oxide and magnesium oxide content respectively shall be at least 75 % by mass.
The composition of Portland-composite cement CEM II/C-M and Composite cement CEM VI covered by this document Is specified in Table 1.BS EN 197-5 pdf free download.composite cement CEM II/C-M and Composite cement CEM VI