www.freestandardsdocuments.com collects the introduction about EN standards.The information will give you some guidance, remember to support my website.

EN 13304:2009 – Bitumen and bituminous binders – Framework for specification of oxidised bitumens

EN 13304:2009 - Bitumen and bituminous binders - Framework for specification of oxidised bitumens

1 Scope This European Standard provides a framework for the specification of oxidised bitumens used mainly in roofing, waterproofing, adhesives and thermal and phonic insulations. Within Europe several types of oxidised bitumens are used and, dependent on climatic conditions, type of building construction and traditional practices, different grades may be used for the same purpose. The framework given in this […]

Continue reading »

EN 13303:2009 – Bitumen and bituminous binders – Determination of the loss in mass after heating of industrial bitumen

EN 13303:2009 - Bitumen and bituminous binders - Determination of the loss in mass after heating of industrial bitumen

1 Scope This European Standard specifies a method for the determination of the loss in mass of industrial bitumen after heating. The method is used to detect volatile components. NOTE The users of the method are encouraged to gather comparative information on binders using this standard,EN 13303 and EN 12607-2 [1] at 163 °C to facilitate the withdrawal of EN […]

Continue reading »

EN 13029:2009 – Packaging – Light-gauge metal packaging – Apertures for plug-in plastic closures

EN 13029:2009 - Packaging - Light-gauge metal packaging - Apertures for plug-in plastic closures

1 Scope This European Standard specifies the dimensions and profile of the aperture for Type A and Type B plug-in plastic closures used in round and non-round metal containers of nominal wall thickness equal to or less than 0,49 mm. 2 General requirements If a burr is produced at the piercing diameter it shall be kept to a minimum to […]

Continue reading »

EN 12790:2009 – Child use and care articles — Reclined cradles

EN 12790:2009 - Child use and care articles — Reclined cradles

1 Scope This standard specifies safety requirements and the corresponding test methods for fixed or folding reclined cradles intended for children up to a weight of 9 kg or who are unable to sit up unaided. This standard applies also to car seats complying with ECE 44 that can be used as reclined cradles according to manufacturer’s instructions. This standard […]

Continue reading »

EN 10238:2009 – Automatically blast-cleaned and automatically prefabrication primed structural steel products

EN 10238:2009 - Automatically blast-cleaned and automatically prefabrication primed structural steel products

1 Scope This European Standard specifies requirements for automatically blast-cleaned and automatically prefabrication primed structural steel products. This European Standard does not cover manual blast cleaning and/or manual spray painting. NOTE Where the steel is less than 5 mm thick, care should be exercised to ensure it is not deformed by blast cleaning. 2 Normative references The following referenced documents […]

Continue reading »

EN 2606:2009 – Aerospace series – 60° interface for adaptors, threaded, with lockring – Geometric configuration

EN 2606:2009 - Aerospace series - 60° interface for adaptors, threaded, with lockring - Geometric configuration

1 Scope This standard specifies the dimensional characteristics of the 60° interface for adaptors, threaded, with lockring, assembly with elastomer O-ring, for aerospace applications. This standard applies to all adaptors, threaded, with lockring, assembled to EN 2607 and used in fluid systems with a nominal pressure of 28 000 kPa for which a metric-size coupling with a 60° conical sealing […]

Continue reading »

EN 1465:2009 – Adhesives – Determination of tensile lap-shear strength of bonded assemblies

EN 1465:2009 - Adhesives - Determination of tensile lap-shear strength of bonded assemblies

1 Scope This European Standard specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing. NOTE 1 This test procedure is not applicable for calculations needed for bond design in structural joints. NOTE 2 This test Test methods for the determination of tensile lap-shear […]

Continue reading »

EN 1430:2009 – Bitumen and bituminous binders – Determination of particle polarity of bituminous emulsions

EN 1430:2009 - Bitumen and bituminous binders - Determination of particle polarity of bituminous emulsions

1 Scope This European Standard specifies a method for the determination of the particle polarity of bituminous emulsions. WARNING — The use of this standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish […]

Continue reading »

EN 1380:2009 – Timber structures – Test methods – Load bearing nails, screws, dowels and bolts

EN 1380:2009 - Timber structures - Test methods - Load bearing nails, screws, dowels and bolts

1 Scope This European Standard specifies test methods for determining the strength and deformation characteristics of laterally loaded connections with nail, screws, dowels and bolts in load-bearing timber structures. The methods assess connections with members of timber (solid timber or glued laminated timber) or wood-based products or metal plates (but not punched metal plate fasteners) in the combination proposed for […]

Continue reading »

EN 15191:2009 – Precast concrete products – Classification of glassfibre reinforced concrete performance

EN 15191:2009 - Precast concrete products - Classification of glassfibre reinforced concrete performance

1 Scope This European Standard deals with the classification of glassfibre reinforced concrete. This classification conforms to the needs of the design process of glassfibre reinforced concrete components. This European Standard applies only if EN 1169 is followed. This standard does not deal with design methods. 2 Normative references The following referenced documents are indispensable for the application of this […]

Continue reading »
1 7 8 9 10 11 56