www.freestandardsdocuments.com collects the introduction about EN standards.The information will give you some guidance, remember to support my website.

BS EN 12773:2000 – Footwear Ð Test methods for outsoles Ð Needle tear strength

BS EN 12773:2000 - Footwear Ð Test methods for outsoles Ð Needle tear strength

Scope This European Standard specifies a method for the determination of the needle tear strength for outsoles, irrespective of the material. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments […]

Continue reading »

BS EN 12947:2000 – Liming materials Ð Determination of magnesium content Ð Atomic absorption spectrometric method

BS EN 12947:2000 - Liming materials Ð Determination of magnesium content Ð Atomic absorption spectrometric method

1 Scope This European Standard specifies a method for the determination of the magnesium content of all liming materials by atomic absorption spectrometry. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, […]

Continue reading »

BS EN 13090:2000 – Means for reseal ing threaded joints of gas pipework in buildings

BS EN 13090:2000 - Means for reseal ing threaded joints of gas pipework in buildings

This European Standard specifies the properties and the test methods of sealants used to reseal ! threaded joints of metallic gas pipework in buildings operated at a maximum allowed operating pressure of 100 mbar (such sealants hereafter are referred to as “sealants”). Note Gas pipework in buildings is in accordance with EN 1775 the pipework between the point of delivery […]

Continue reading »

BS EN 13193:2000 – Packaging Ð Packaging and the environment Ð Terminology

BS EN 13193:2000 - Packaging Ð Packaging and the environment Ð Terminology

1Scope This standard defines terms used in the field of Packaging and the Environment. 2Terminology The following principles are used as a basis : -no preference is implied between the different methods of recovery ; -no preference is implied between different packaging materials. The terms are divided between three clauses. Clause 3 contains terms which are specifically related topackaging and […]

Continue reading »

BS EN 13318:2000 – Screed material and floor screeds Ð Definitions

BS EN 13318:2000 - Screed material and floor screeds Ð Definitions

This European Standard defines terms, which are used in the production and application of screed material and floor screeds. The terms are valid for all standards repared by TC 303. 2.1 Base Buildingelement whichprovides the support for a screed. 22l screed Layer or llayers of screedmaterial laid insitu,directly onto abase. bonded or unbonded. or ontoan intermediatelayerorinsulating layer.to obtain one or […]

Continue reading »

BS EN 13510:2000 – Earth-moving machinery Ð Roll-over protective structures Ð Laboratory tests and performance requirements Ð

BS EN 13510:2000 - Earth-moving machinery Ð Roll-over protective structures Ð Laboratory tests and performance requirements Ð

This European Standard establishes a consistent and reproducible means of evaluating the load-carrying characteristics of Roll-Over Protective Structures (ROPS) under static loading,and prescribes performance requirements for a representative specimen under such loading. It applies to the following seated design operator-controlled machines as defined in ISO 6165: – dozers (crawler and wheeled); – graders; – loaders (crawler and wheeled); – earth- […]

Continue reading »

BS EN 60445:2000 – Basic and safety principles for man-machine interface, marking and identification – Identification of equipment terminals, conductor terminations and conductors

BS EN 60445:2000 - Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors

1 Scope This document applies to the identification and marking of terminals of electrical equipment such as resistors, fuses, relays, contactors, transformers, rotating machines and, wherever applicable, to combinations of such equipment (e.g. assemblies), and also applies to the identification of terminations of certain designated conductors. It also provides general rules for the use of certain colours or alphanumeric notations […]

Continue reading »

BS EN 10020:2000 – efinition and classification of rades of steel

BS EN 10020:2000 - efinition and classification of rades of steel

1 Scope This European Standard defines the term “steel” (see clause 2) and classifies steel grades into: – non alloy, stainless steel and other alloy steels by chemical composition (see clause 3); – main quality classes (see clause 4) defined by main property or application characteristics for non alloy, stainless and other alloy steels. 2 Term and definition For the […]

Continue reading »

BS EN 12706:2000 – Adhesives Ð Test methods for hydraulic setting floor smoothing and/or levelling

BS EN 12706:2000 - Adhesives Ð Test methods for hydraulic setting floor smoothing and/or levelling

1 Scope This European Standard specifies a test method to assess the flow characteristics of a hydraulic setting floor smoothing and/or levelling compounds. Hydraulic setting floor smoothing and/or levelling compounds are referred to as “smoothing and/or levelling compound” when mixed with water and/or mixing liquid according to the manufacturers’ instructions. 2 Normative references This European Standard incorporates by dated or […]

Continue reading »

EN 143:2000 – Respiratory protective devices – Particle filters – Requirements, testing, marking

EN 143:2000

This European Standard specifies particle filters for use as components in unassisted respiratory protective devices with the exception of escape apparatus and filtering facepieces. Laboratory tests are included for the assessment of compliance with the requirements. Some filters complying with this European Standard may also be suitable for use with other types of respiratory protective devices and, if so, shall […]

Continue reading »
1 54 55 56