www.freestandardsdocuments.com collects the introduction about EN standards.The information will give you some guidance, remember to support my website.

BS EN 13209-1:2004 – Child use and care articles — Baby carriers — Safety requirements and test methods — Part 1: Framed back carriers

BS EN 13209-1:2004 - Child use and care articles — Baby carriers — Safety requirements and test methods — Part 1: Framed back carriers

1 Scope This document specifies the safety requirements and test methods for child back carriers with framed support. These framed carriers are intended for children who can sit unaided (approximately 6 months of age) and are designed to be attached to a carer‟s torso allowing a “hands free operation” when standing and/or walking. 2 Normative references The following referenced documents […]

Continue reading »

BS EN 13141-5:2004 – Ventilation for buildings — Performance testing of components/products for residential ventilation — Part 5: Cowls and roof outlet terminal devices

BS EN 13141-5:2004 - Ventilation for buildings — Performance testing of components/products for residential ventilation — Part 5: Cowls and roof outlet terminal devices

1 Scope This document specifies methods for measuring the aerodynamic and acoustic characteristics of cowls and roof outlets used in both natural and mechanical ventilation. Only those cowls and roof outlets fitted onto ducts which project above the roof surface are covered by the present standard. Regarding the assisted cowls, only the fan assisted cowls are covered by the present […]

Continue reading »

BS EN 13130-7:2004 – Materials and articles in contact with foodstuffs — Plastics substances subject to limitation — Part 7: Determination of monoethylene glycol and diethylene glycol in food simulants

BS EN 13130-7:2004 - Materials and articles in contact with foodstuffs — Plastics substances subject to limitation — Part 7: Determination of monoethylene glycol and diethylene glycol in food simulants

1 Scope This part of this European Standard specifies methods for the determination of monoethylene glycol and diethylene glycol in the food simulants; water, 3 % (w/v) acetic acid, 15 % (v/v) ethanol and olive oil and other fatty food simulants, simulants D, e.g. a mixture of synthetic triglycerides or sunflower oil or corn oil. The methods are capable of […]

Continue reading »

BS EN 13057:2002 – Products and systems for the protection and repair of concrete structures — Test methods — Determination of resistance of capillary absorption

BS EN 13057:2002 - Products and systems for the protection and repair of concrete structures — Test methods — Determination of resistance of capillary absorption

1 Scope This European Standard is one of a series dealing with products and systems for the protection and repair of concrete structures. It specifies a method for determining the resistance to water absorption of repair products and systems, as defined in prEN 1 504-3 1 . The method is based on measuring the increase in weight due to capillary […]

Continue reading »

BS EN 12365-3:2003 – Building hardware — Gasket and weatherstripping for doors, windows, shutters and curtain walling — Part 3: Deflection recovery test method

BS EN 12365-3:2003 - Building hardware — Gasket and weatherstripping for doors, windows, shutters and curtain walling — Part 3: Deflection recovery test method

1 Scope This standard specifies the method to be used to select, prepare, condition and test samples of gaskets or weatherstripping, to determine the percentage of recovery after being compressed or deflected through their working range to the minimum width under the conditions laid down in the test. 2 Normative references This European Standard incorporates by dated or undated reference, […]

Continue reading »

BS EN 12258-4:2004 – Aluminium and aluminium alloys — Terms and definitions — Part 4: Residues of the aluminium industry

BS EN 12258-4:2004 - Aluminium and aluminium alloys — Terms and definitions — Part 4: Residues of the aluminium industry

This document contains definitions of terms which are helpful for the communication within the aluminium industry, authorities and subcontractors dealing with the shipment, recovery or disposal of residues. It only contains residues which are specific for the aluminium industry. Residues which generally occur with identical inherent properties in other industries and private households are defined in prEN 13965-1. This document […]

Continue reading »

BS EN 12237:2003 – Ventilation for buildings — Ductwork — Strength and leakage of circular sheet metal ducts

BS EN 12237:2003 - Ventilation for buildings — Ductwork — Strength and leakage of circular sheet metal ducts

1 Scope This European Standard specifies requirements and test methods for strength and air leakage of circular ductwork used in air conditioning and ventilation systems in buildings. The standard is intended to establish the mechanical strength and leakage required to verify the fitness for the intended service as installed ductwork. The standard is intended for testing specific installations as well […]

Continue reading »

BS EN 10331:2003 – Magnetic materials — Specification for sintered soft magnetic materials

BS EN 10331:2003 - Magnetic materials — Specification for sintered soft magnetic materials

1 Scope This European Standard specifies some magnetic and mechanical properties of sintered soft magnetic metals which are used for components made by a powder metallurgical process only. This standard does not apply to magnetically soft castings or to semi-finished products. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references […]

Continue reading »

BS EN 10025-3:2004 – Hot rolled products of structural steels — Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels

BS EN 10025-3:2004 - Hot rolled products of structural steels —

1 Scope Part 3 of this document, in addition to part 1 , specifies requirements for flat and long products of hot rolled weldable fine grain structural steels in the normalized/normalized rolled delivery condition in the grades and qualities given in Tables 2 to 4 (chemical composition) and Tables 5 to 7 (mechanical properties) in thickness ≤ 250 mm for […]

Continue reading »

BS EN 10025-1:2004 – Hot rolled products of structural steels — Part 1: General technical delivery conditions

BS EN 10025-1:2004 - Hot rolled products of structural steels — Part 1: General technical delivery conditions

1 Scope 1.1 This document specifies requirements for flat and long products (see Clause 3) of hot rolled structural steels excluding structural hollow sections and tubes. Part 1 of this document specifies the general delivery conditions. The specific requirements for structural steels are given in the following Parts: Part 2: Technical delivery conditions for non-alloy structural steels Part 3: Technical […]

Continue reading »
1 40 41 42 43 44 56