www.freestandardsdocuments.com collects the introduction about EN standards.The information will give you some guidance, remember to support my website.

BS EN 14532-1:2004 – Welding consumables — Test methods and quality requirements — Part 1: Primary methods and conformity assessment of consumables for steel, nickel and nickel alloys

BS EN 14532-1:2004 - Welding consumables — Test methods and quality requirements — Part 1: Primary methods and conformity assessment of consumables for steel, nickel and nickel alloys

1 Scope This document describes the basic verification tests, the testing methods, the amount of testing and the requirements for the qualification of welding consumables for steel, nickel and nickel alloys intended for all fields of application. This document describes a wide range of tests, which are appropriate for the majority of applications. When supplementary tests are required (see EN […]

Continue reading »

BS EN 50290-1-2:2004 – Communication cables — Part 1-2: Definitions

BS EN 50290-1-2:2004 - Communication cables — Part 1-2: Definitions

1 Scope This Part 1 -2 of the European Standard EN 50290 gives the terms and definitions for the design, the construction, the tests and the installation of symmetrical, coaxial and optical fibre cables used for the infrastructure of communication and control networks. These definitions apply for the European Standard series EN 50290 and EN 50289 and all the relevant […]

Continue reading »

BS EN 60745-2-4:2003 – Hand-held motor-operated electric tools — Safety — Part 2-4: Particular requirements for sanders and polishers other than disk type

BS EN 60745-2-4:2003 - Hand-held motor-operated electric tools — Safety — Part 2-4: Particular requirements for sanders and polishers other than disk type

1 Scope This clause of Part 1 is applicable, except as follows: 1 .1 Addition: This standard applies to sanders and polishers with the exception of all types of rotating disc-type sanders, which are covered by EN 60745-2-3. NOTE Until publication of EN 60745-2-3, rotating disc-type sanders are covered by EN 501 44-2-3. Tools covered by this standard include but […]

Continue reading »

BS EN 60819-3-1:2001 – Non-cellulosic papers for electrical purposes — Part 3: Specifications for individual materials — Sheet 1: Filled glass paper

BS EN 60819-3-1:2001 - Non-cellulosic papers for electrical purposes — Part 3: Specifications for individual materials — Sheet 1: Filled glass paper

1 Scope This sheet of IEC 6081 9-3 specifies requirements for two types of filled glass paper designated: P-FG type 1 : high inorganic content paper with maximum organic content 1 5 %; P-FG type 2: medium inorganic content paper with maximum organic content 25 %. 2 Normative references The following normative documents contain provisions which, through reference in the […]

Continue reading »

BS EN 61108-4:2004 – Maritime navigation and radiocommunication equipment and systems — Global navigation satellite systems (GNSS) — Part 4: Shipborne DGPS and DGLONASS maritime radio beacon receiver equipment — Performance requirements, methods of testing and required test results

BS EN 61108-4:2004 - Maritime navigation and radiocommunication equipment and systems — Global navigation satellite systems (GNSS) — Part 4: Shipborne DGPS and DGLONASS maritime radio beacon receiver equipment — Performance requirements, methods of testing and required test results

1 Scope This part of IEC 61 1 08 specifies the minimum operational and performance requirements, methods of testing and required test results conforming to performance standards not inferior to those adopted by the IMO in resolution MSC.1 1 4(73). In addition, it takes account of IMO resolution A.694(1 7) and is associated with IEC 60945. When a requirement of […]

Continue reading »

BS EN 61340-4-5:2004 – Electrostatics — Part 4-5: Standard test methods for specific applications — Methods for characterizing the electrostatic protection of footwear and flooring in combination with a person

BS EN 61340-4-5:2004 - Electrostatics — Part 4-5: Standard test methods for specific applications — Methods for characterizing the electrostatic protection of footwear and flooring in combination with a person

5 Atmosphere for conditioning and testing The following requirements supersede any other specification for the atmosphere for conditioning and testing that may be given in one or more of the documents referred to in this standard. Unless otherwise agreed, the atmosphere for conditioning and testing for laboratory evaluations shall be (23 ± 2) °C and (1 2 ± 3) % […]

Continue reading »

BS EN 61959:2004 – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Mechanical tests for sealed portable secondary cells and batteries

BS EN 61959:2004 - Secondary cells and batteries containing alkaline or other non-acid electrolytes — Mechanical tests for sealed portable secondary cells and batteries

1 Scope This International standard specifies tests and requirements for verifying the mechanical behaviour of sealed portable secondary cells and batteries during handling and normal use. Relevant national and International standards have been taken into consideration. This standard provides test objectives, methods of tests and acceptance criteria relevant to sealed portable secondary cells and batteries of d ifferent electrochemical systems […]

Continue reading »

BS EN 62270:2004 – Hydroelectric power plant automation — Guide for computor-based control

BS EN 62270:2004 - Hydroelectric power plant automation — Guide for computor-based control

1 Overview 1.1 Scope This standard sets down guidelines for the application, design concepts, and implementation of computer-based control systems for hydroelectric plant automation. It addresses functional capabilities, performance requirements, interface requirements, hardware considerations, and operator training. It includes recommendations for system testing and acceptance. Finally, case studies of actual computer-based automatic control applications are presented. The automation of control […]

Continue reading »

BS EN ISO 10434:2004 – Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries

BS EN ISO 10434:2004 - Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries

1 Scope This International Standard specifies the requirements for a heavy-duty series of bolted bonnet steel gate valves for petroleum refinery and related applications where corrosion, erosion and other service conditions would indicate a need for full port openings, heavy wall sections and large stem diameters. This International Standard sets forth the requirements for the following gate valve features: bolted […]

Continue reading »

BS EN ISO 11904-2:2004 – Acoustics — Determination of sound immission from sound sources placed close to the ear — Part 2: Technique using a manikin

BS EN ISO 11904-2:2004 - Acoustics — Determination of sound immission from sound sources placed close to the ear — Part 2: Technique using a manikin

1 Scope This part of ISO 1 1 904 specifies basic framework measurement methods for sound immission from sound sources placed close to the ear. These measurements are carried out with a manikin, equipped with ear simulators including microphones. The measured values are subsequently converted into corresponding freefield or diffuse-field levels. The results are given as free-field related or diffuse-field […]

Continue reading »
1 38 39 40 41 42 56