www.freestandardsdocuments.com collects the introduction about EN standards.The information will give you some guidance, remember to support my website.

BS EN 62093:2005 – Balance-of-system components for photovoltaic systems — Design qualification natural environments

BS EN 62093:2005 - Balance-of-system components for photovoltaic systems — Design qualification natural environments

1 Scope and object This International Standard establishes requirements for the design qualification of balance- of-system (BOS) components used in terrestrial photovoltaic (PV) systems. This standard is suitable for operation in indoor, conditioned or unconditioned; or outdoor in general open-air climates as defined in IEC 60721 -2-1 , protected or unprotected. It is written for dedicated solar components such as […]

Continue reading »

BS EN 61966-6:2006 – Multimedia systems and equipment — Colour measurement and management — Part 6: Front projection displays

BS EN 61966-6:2006 - Multimedia systems and equipment — Colour measurement and management — Part 6: Front projection displays

1 Scope This part of IEC 61 966 defines input test signals, measurement conditions, methods of measurement and reporting of the measured data, to be used for colour characterization and colour management of front projection displays in multimedia systems. Colour control within equipment is outside the scope of this part. It does not specify limiting values for various parameters. 2 […]

Continue reading »

BS EN 61243-1:2005 – Live working — Voltage detectors — Part 1: Capacitive type to be used for voltages exceeding 1 kV a.c.

BS EN 61243-1:2005 - Live working — Voltage detectors — Part 1: Capacitive type to be used for voltages exceeding 1 kV a.c.

4.2 Functional requirements 4.2.1 Clear indication The voltage detector shall clearly indicate the presence and/or the absence of the system operating voltage as a function of the nominal voltage or nominal voltage range of the voltage detector, and its nominal frequency or nominal frequencies. 4.2.1 .1 Threshold voltage The indication “voltage present” shall appear if the voltage to ground on […]

Continue reading »

BS EN 61000-6-2:2005 – Electromagnetic compatibility (EMC) — Part 6-2: Generic standards — Immunity for industrial environments

BS EN 61000-6-2:2005 - Electromagnetic compatibility (EMC) — Part 6-2: Generic standards — Immunity for industrial environments

1 Scope and object This part of IEC 61 000 for EMC immunity requirements applies to electrical and electronic apparatus intended for use in industrial environments, as described below. Immunity requirements in the frequency range 0 Hz to 400 GHz are covered. No tests need to be performed at frequencies where no requirements are specified. This generic EMC immunity standard […]

Continue reading »

BS EN 60904-1:2006 – Photovoltaic devices — Part 1: Measurement of photovoltaic current-voltage characteristics

BS EN 60904-1:2006 - Photovoltaic devices — Part 1: Measurement of photovoltaic current-voltage characteristics

5.1 Mount the reference device as near as possible to and co-planar with the specimen on the two-axis tracker. Both shall be normal to the direct solar beam within ±5°. Connect to the necessary instrumentation. 5.2 If the specimen and reference device are equipped with temperature controls, set the controls at the desired level. If temperature controls are not used: […]

Continue reading »

BS EN 60898-2:2006 – Electrical accessories — Circuit-breakers for overcurrent protection for household and similar installations — Part 2: Circuit-breakers for a.c and d.c. operation

BS EN 60898-2:2006 - Electrical accessories — Circuit-breakers for overcurrent protection for household and similar installations — Part 2: Circuit-breakers for a.c and d.c. operation

1 Scope and object This clause of Part 1 is applicable except as follows: Addition at the end of the first paragraph: This standard gives additional requirements for single- and two-pole circuit-breakers which, in addition to the above characteristics, are suitable for operation with direct current, and have a rated d.c. voltage not exceeding 220 V for single-pole and 440 […]

Continue reading »

BS EN 60384-23-1:2005 – Fixed capacitors for use in electronic equipment — Part 23-1: Blank detail specification — Fixed surface mount metallized polyethylene naphthalate film dielectric DC capacitors — Assessment level EZ

BS EN 60384-23-1:2005 - Fixed capacitors for use in electronic equipment — Part 23-1: Blank detail specification — Fixed surface mount metallized polyethylene naphthalate film dielectric DC capacitors — Assessment level EZ

1 General data 1 .1 Recommended method(s) of mounting (to be inserted) See 1 .4.2 of IEC 60384-23. 1 .2 Dimensions When there is no case size reference, Table 1 may be omitted and the dimensions shall be given in Table 2, which then becomes Table 1 . The dimensions shall be given as maximum dimensions or as nominal dimensions […]

Continue reading »

BS EN 60118-8:2005 – Electroacoustics — Hearing aids — Part 8: Methods of measurement of performance characteristics of hearing aids under simulated in situ working conditions

BS EN 60118-8:2005 - Electroacoustics — Hearing aids — Part 8: Methods of measurement of performance characteristics of hearing aids under simulated in situ working conditions

3.1 sound pressure level throughout this standard all sound pressure levels (abbreviated SPL) are referred to 20 μPa 3.2 pinna simulator device which has the approximate shape and dimensions of a median adult human pinna 3.3 ear simulator device for measuring the output sound pressure level of an earphone under well defined loading conditions in a specified frequency range. It […]

Continue reading »

BS EN 50470-3:2006 – Electricity metering equipment (a.c.) — Part 3: Particular requirements — Static meters for active energy (class indexes A, B and C)

BS EN 50470-3:2006 - Electricity metering equipment (a.c.) — Part 3: Particular requirements — Static meters for active energy (class indexes A, B and C)

1 Scope This European Standard applies to newly manufactured static watt-hour meters intended for residential, commercial and light industrial use, of class indexes A, B and C, for the measurement of alternating current electrical active energy in 50 Hz networks. It specifies particular requirements and type test methods. It applies to static watt-hour meters for indoor and outdoor application, consisting […]

Continue reading »

BS EN 50290-2-1:2005 – Communication cables — Part 2-1: Common design rules and construction

BS EN 50290-2-1:2005 - Communication cables — Part 2-1: Common design rules and construction

1 Scope This European Standard harmonises the standardisation of symmetrical, coaxial and optical cables used for the infrastructure of communication, multimedia and control networks. Most of the cables covered by this European Standard are primarily intended to be used in IT networks. However, they can also be used for other applications with the exception of those which presume a direct […]

Continue reading »
1 30 31 32 33 34 56