www.freestandardsdocuments.com collects the introduction about EN standards.The information will give you some guidance, remember to support my website.

EN 14600:2005 – Doorsets and openable windows with fire resisting and/or smoke control characteristics – Requirements and classification

EN 14600:2005 - Doorsets and openable windows with fire resisting and/or smoke control characteristics - Requirements and classification

1 Scope This European Standard identifies the particular requirements and classifications necessary to demonstrate the characteristics of fire resistance, smoke leakage control and self closing durability for pedestrian doorsets,industrial type doorsets and openable windows. Requirements for performance characteristics for these products can be found in the appropriate product standards. This document does not cover any component reliability or durability testing […]

Continue reading »

EN 14529:2005 – Respiratory protective devices – Self-contained open-circuit compressed air breathing apparatus with half mask designed to include a positive pressure lung governed demand valve for escape purposes only

EN 14529:2005 - Respiratory protective devices - Self-contained open-circuit compressed air breathing apparatus with half mask designed to include a positive pressure lung governed demand valve for escape purposes only

1 Scope This European Standard specifies minimum requirements for self-contained open-circuit compressed air breathing apparatus with half mask designed to include a positive pressure lung governed demand valve for escape purposes only. Such equipment is intended for use in work situations where the risk on overpressurisation of the pressure vessels with their valves due to hot environmental conditions is low. […]

Continue reading »

EN 14519:2005 – Solid softwood panelling and cladding – Machined profiles with tongue and groove

EN 14519:2005 - Solid softwood panelling and cladding - Machined profiles with tongue and groove

1 Scope This European Standard specifies the characteristics of solid wood panelling and cladding with tongue and groove machined from the following most common European species of softwood: spruce/fir, pine, larch,European Douglas Fir and maritime pine. Products are intended for interior or exterior use. NOTE Products sold in the European Economic Area should comply with prEN 14915. 2 Normative references […]

Continue reading »

EN 14506:2005 – Devices to prevent pollution by backflow of potable water – Automatic diverter – Family H, type C

EN 14506:2005 - Devices to prevent pollution by backflow of potable water - Automatic diverter - Family H, type C

1 Scope This document specifies: a) field of application; b) requirements for automatic diverters; c) dimensional and the physico-chemical properties and the properties of general hydraulic, mechanical and acoustic design of automatic diverters; d) test method and requirements for verifying these properties. For sanitary tapware (see Clause 2) with integrated devices, the automatic diverter is only considered to be a […]

Continue reading »

EN 14455:2005 – Devices to prevent pollution by backflow of potable water – Pressurised air inlet valves DN 1 5 to DN 50 – Family L, type A and type B

EN 14455:2005 - Devices to prevent pollution by backflow of potable water - Pressurised air inlet valves DN 1 5 to DN 50 - Family L, type A and type B

1 Scope This document specifies: a) field of application; b) requirements for pressurised air inlet valves; c) dimensional and the physico-chemical properties and the properties of general hydraulic, mechanical and acoustic design of pressurised air inlet valves DN 15 to DN 50; d) test procedure and requirements for verifying these properties; e) marking and presentation; f) acoustics. This document specifies […]

Continue reading »

EN 14449:2005 – Glass in building – Laminated glass and laminated safety glass – Evaluation of conformity/Product standard

EN 14449:2005 - Glass in building - Laminated glass and laminated safety glass - Evaluation of conformity/Product standard

4.3.2.4 Safety in use – Bullet resistance: shatter properties and resistance to attack Bullet resistance shall be determined and classified in accordance with EN 1063. 4.3.2.5 Safety in use – Explosion resistance: impact behaviour and resistance to impact Explosion resistance shall be determined and classified in accordance with EN 13541. 4.3.2.6 Safety in use – Burglar resistance: shatter properties and […]

Continue reading »

EN 13956:2005 – Flexible sheet for waterproofing — Plastic and rubber sheets for roof waterproofing — Definitions and characteristics

EN 13956:2005 - Flexible sheet for waterproofing — Plastic and rubber sheets for roof waterproofing — Definitions and characteristics

1 Scope This European Standard specifies the definitions and characteristics of plastic and rubber sheets including sheets made out of their blends and alloys (thermoplastic rubber) for which the intended use is roof waterproofing. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard. NOTE For […]

Continue reading »

EN 10207:2005 – Steels for simple pressure vessels – Technical delivery requirements for plates, strips and bars

EN 10207:2005 - Steels for simple pressure vessels - Technical delivery requirements for plates, strips and bars

1 Scope This document specifies the technical delivery requirements for flat products and bars made of steel in accordance with the specifications for pressurized parts in simple pressure vessels as defined in the Directive 87/404/EEC(see Annex A) and standardized in EN 286-1 to -3. 2 Normative references The following referenced documents are indispensable for the application of this document. For […]

Continue reading »

EN 10080:2005 – Steel for the reinforcement of concrete – Weldable reinforcing steel – General

EN 10080:2005 - Steel for the reinforcement of concrete - Weldable reinforcing steel - General

1 Scope 1.1 This European Standard specifies general requirements and definitions for the performance characteristics of weldable reinforcing steel used for the reinforcement of concrete structures, delivered as finished products in the form of: bars, coils (rod, wire) and de-coiled products; sheets of factory-made machine-welded fabric; lattice girders. 1.2 Steels according to this European Standard have a ribbed, indented or […]

Continue reading »

EN 2608:2005 – Aerospace series – Installation and removal requirements for 8° 30′ adaptors, threaded, with lockring

EN 2608:2005 - Aerospace series - Installation and removal requirements for 8° 30' adaptors, threaded, with lockring

1 Scope This standard specifies the installation and removal requirements for adaptors, threaded, with lockring for pipe couplings 8°30′ according to EN 2603. This standard establishes an accurate procedure of adaptor installation, removal and reinstallation to ensure the repeatability of the installation operation and to ensure the effective compliance to sealing and locking requirements. The adaptor shown on all figures […]

Continue reading »
1 28 29 30 31 32 56