www.freestandardsdocuments.com collects the introduction about EN standards.The information will give you some guidance, remember to support my website.

EN 15334:2007 – Sanitary appliances – Methacrylic dispersions of high filler content

EN 15334:2007 - Sanitary appliances - Methacrylic dispersions of high filler content

1 Scope This European Standard specifies test methods for measuring characteristics of pure methacrylic dispersions and sanitary appliances produced from dispersions by polymerisation. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. […]

Continue reading »

EN 15275:2007 – Structural adhesives – Characterisation of anaerobic adhesives for co-axial metallic assembly in building and civil engineering structures

EN 15275:2007 - Structural adhesives - Characterisation of anaerobic adhesives for co-axial metallic assembly in building and civil engineering structures

Indicative performance requirements are given in Annex A depending on the intended use. These values are drawn from laboratory and practical experience and can be considered to indicate satisfactory performance under normal practical use and conditions. The torque strength of anaerobic adhesives on threaded fasteners is expressed as breakloose torque measured on assemblies preloaded with an input torque of 5 […]

Continue reading »

EN 15255:2007 – Energy performance of buildings – Sensible room cooling load calculation – General criteria and validation procedures

EN 15255:2007 - Energy performance of buildings - Sensible room cooling load calculation - General criteria and validation procedures

1 Scope This European Standard sets out the level of input and output data, and prescribes the boundary conditions equired for a calculation method of the sensible cooling load of a single room under constant and/or floating temperature taking into account the limit of the peak cooling load of the system. It includes a classification scheme of the calculation method […]

Continue reading »

EN 15251:2007 – Indoor environmental input parameters for design and assessment of energy performance of buildings addressing indoor air quality, thermal environment, lighting and acoustics

EN 15251:2007 - Indoor environmental input parameters for design and assessment of energy performance of buildings addressing indoor air quality, thermal environment, lighting and acoustics

Criteria specified in national building codes for design and dimensioning of systems shall be used. The present standard gives, in informative annexes, recommended input values for use in cases where no national regulation are available. The recommended criteria are given for several categories. Design criteria for the indoor environment shall be documented by the designer. Design criteria for the indoor […]

Continue reading »

EN 15095:2007 – Power-operated mobile racking and shelving, carousels and storage lifts – Safety requirements

EN 15095:2007 - Power-operated mobile racking and shelving, carousels and storage lifts - Safety requirements

1 Scope 1.1 This European Standard deals with the safety requirements for the following types of power-operated storage equipment: storage carousels; storage lifts; mobile shelving, pallet racking and cantilever racking with the objective of eliminating or minimising the hazards described in Clause 4. These hazards can arise during installation, starting up, operation, maintenance, testing and dismantling of the equipment. 1.2 […]

Continue reading »

EN 15026:2007 – Hygrothermal performance of building components and building elements – Assessment of moisture transfer by numerical simulation

EN 15026:2007 - Hygrothermal performance of building components and building elements - Assessment of moisture transfer by numerical simulation

1 Scope This standard specifies the equations to be used in a simulation method for calculating the non steady transfer of heat and moisture through building structures. It also provides a benchmark example intended to be used for validating a simulation method claiming conformity with this standard, together with the allowed tolerances. The equations in this standard take account of […]

Continue reading »

EN 14768:2005 – Fibreboard drums – Removable head (open head) drums with slip on lids with a nominal capacity of 5 l to 600 l

EN 14768:2005 - Fibreboard drums - Removable head (open head) drums with slip on lids with a nominal capacity of 5 l to 600 l

1 Scope This document specifies the construction requirements for cylindrical fibreboard drums with slip on lids with a nominal capacity of 5 l to 600 l and the preferred range of diameters for drums with a circular cross-section and preferred dimensions for drums with a rectangular cross section. 2 Normative references The following referenced documents are indispensable for the application […]

Continue reading »

EN 14682:2007 – Safety of children’s clothing — Cords and drawstrings on children’s clothing — Specifications

EN 14682:2007 - Safety of children’s clothing — Cords and drawstrings on children’s clothing — Specifications

3 Requirements 3.1 General 3.1.1 The free ends of drawstrings, functional cords, and tied belts or sashes shall have no three- dimensional embellishments or knot and shall be secured to prevent fraying, for example by heat sealing or bar tacking. The ends may be doubled or folded provided no hazard of entrapment is created. 3.1.2 Toggles shall only be used […]

Continue reading »

EN 14669:2005 – Surface active agents – Determination of anionic surface active agents and soaps in detergents and cleansers – Potentiometric two-phase titration method

EN 14669:2005 - Surface active agents - Determination of anionic surface active agents and soaps in detergents and cleansers - Potentiometric two-phase titration method

1 Scope This European Standard specifies a method for the determination of the content of anionic surface active agents and soaps in detergents and cleansers, defined as being the amount of anionic surface active agents expressed in millimoles per 100 g of product. NOTE 1 The applicability in products different that those tested should be checked in each particular case. […]

Continue reading »

EN 14668:2005 – Surface active agents – Determination of quaternary ammonium surface active agents in raw materials and formulated products – Potentiometric two-phase titration method

EN 14668:2005 - Surface active agents - Determination of quaternary ammonium surface active agents in raw materials and formulated products - Potentiometric two-phase titration method

1 Scope This European Standard specifies a method for the determination of the content of quaternary ammonium surface active agents in raw materials and formulated products, defined as being the amount of quaternary ammonium surface active agents expressed in millimoles per 100 g of product. NOTE 1 The applicability in products different than those tested should be checked in each […]

Continue reading »
1 21 22 23 24 25 56