BS EN 14639:2005 – Crude tar and crude benzole — Characteristics and test methods

BS EN 14639:2005 - Crude tar and crude benzole — Characteristics and test methods

1 Scope This European Standard defines the methods of tests for the determination of the characteristics of crude tar and crude benzole. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN […]

Continue reading »

BS EN 14383-1:2006 – Prevention of crime — Urban planning and building design — Part 1: Definition of specific terms

BS EN 14383-1:2006 - Prevention of crime — Urban planning and building design — Part 1: Definition of specific terms

1Scope This European Standard is thetermilinology part of a series for thePrevention’ ofcrime by urbanplanning and building design. Forsome spocilic terms usod in theother parts,dealing woith urbanplanining. dwellings,shops and offices. it provides equivalent termsinthree ‘languages.as well asdetinitions. 2Normative references Not applicable. 3Terms and definitions 3.1 access control setoftechniques,means,procedures allowing’ levels ofaocess .rights and optionally thetraceability of acoess to a site […]

Continue reading »

BS EN 13900-5:2005 – Pigments and extenders — Methods of dispersion and assessment of dispersibility in plastics — Part 5: Determination by filter pressure value test

BS EN 13900-5:2005 - Pigments and extenders — Methods of dispersion and assessment of dispersibility in plastics — Part 5: Determination by filter pressure value test

6.6 Filter 6.6.1 General The filter media is that part of the system which influences the differential pressure used as the basic data for determining the results of the test. The differential pressure increase is dependent on the retention characteristics of the filter media. In order to have comparable results it is important that the filter media is defined in […]

Continue reading »

BS EN 13566-7:2007 – Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 7: Lining with spirally-wound pipes

BS EN 13566-7:2007 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 7: Lining with spirally-wound pipes

1 Scope This part of EN 1 3566, read in conjunction with EN 1 3566-1 , specifies requirements and test methods for pipes that are formed on site by spirally winding and jointing a pre-manufactured profiled plastics strip using a dedicated winding machine in front of the open end of an existing pipeline (e.g. in a manhole). The pipes thus […]

Continue reading »

BS EN 12953-9:2007 – Shell boilers — Part 9: Requirements for limiting devices of the boiler and accessories

BS EN 12953-9:2007 - Shell boilers — Part 9: Requirements for limiting devices of the boiler and accessories

1 Scope This European Standard specifies requirements for limiters (or limiting devices) which are incorporated into safety systems for shell boilers as defined in EN 1 2953-1 . A limiter (or limiting device) can be either: a safety accessory as defined in the Pressure Equipment Directive, Article 1 , clause 2.1 .3, and needs to include the safety logic and […]

Continue reading »

BS EN 12798:2007 – Transport quality system — Road rail and inland navigation transport — Quality system requirements to supplement EN 9002 for the transport of dangerous goods, with regard to safety

BS EN 12798:2007 - Transport quality system — Road rail and inland navigation transport — Quality system requirements to supplement EN 9002 for the transport of dangerous goods, with regard to safety

4.2 Documentation requirements 4.2.1 General EN ISO 9001 :2000, 4.2.1 and the following additional requirements apply. A company profile shall be available with the following key elements: General data: a) Name and address of head office; b) Legal company status; c) Line of business. Data concerning the transport of dangerous goods: d) Name and address of any other depots and […]

Continue reading »

BS EN 12698-1:2007 – Chemical analysis of nitride bonded silicon carbide refractories — Part 1: Chemical methods

BS EN 12698-1:2007 - Chemical analysis of nitride bonded silicon carbide refractories — Part 1: Chemical methods

1 Scope This standard describes the methods for the analysis of all refractory products containing nitride and oxynitride bonded silicon carbide, irrespective of the silicon carbide level. It includes details of sample preparation, general principles of chemical analysis and detailed methods for the determination of carbon,silicon carbide, free aluminium, free silicon, total nitrogen and oxygen. 2 Normative references The following […]

Continue reading »

BS EN 10340:2007 – Steel castings for structural uses

BS EN 10340:2007 - Steel castings for structural uses

1 Scope This European Standard applies to steel castings: for structural uses in buildings and civil engineering works. Its uses include housing and service buildings,bridges, roads, pipe network. In cases where castings are joined by welding by the founder, this European Standard applies. This European Standard does not apply in cases where castings are welded: to wrought products (plates, tubes, […]

Continue reading »

BS EN 10292:2007 – Continuously hot-dip coated strip and sheet of steels with high yield strength for cold forming — Technical delivery conditions

BS EN 10292:2007 - Continuously hot-dip coated strip and sheet of steels with high yield strength for cold forming — Technical delivery conditions

1 Scope This European Standard specifies requirements for continuously hot-dip zinc (Z), zinc-iron alloy (ZF), zincaluminium alloy (ZA), aluminium-zinc alloy (AZ) and aluminium-silicon alloy (AS) coated flat products made of steels with high yield strength for cold forming (see Tables 1 and 3) with thicknesses up to and including 3,0 mm unless otherwise agreed. The thickness is the final thickness […]

Continue reading »

BS EN 10226-2:2005 – Pipe threads where pressure tight joints are made on the threads — Part 2: Taper, external threads and taper internal threads — Dimensions, tolerances and designation

BS EN 10226-2:2005 - Pipe threads where pressure tight joints are made on the threads — Part 2: Taper, external threads and taper internal threads — Dimensions, tolerances and designation

1 Scope This European Standard specifies the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1 /1 6 to 6 inclusive, for joints made pressure-tight by the mating of the threads. These threads are taper external and taper internal and are intended for use with pipes suitable for threading and for valves, fittings or other […]

Continue reading »
1 26 27 28 29 30 80