EN 1270:2005 – Playing field equipment – Basketball equipment – Functional and safety requirements, test methods

EN 1270:2005 - Playing field equipment - Basketball equipment - Functional and safety requirements, test methods

1 Scope This European Standard specifies functional requirements (see Clause 3) and safety requirements (see Clause 4) for basketball equipment. This European Standard is applicable to 8 types of basketball equipment within the classes A to E (see 3.1). This European Standard is not applicable to home basketball equipment, which is considered to be covered by EN 71-1, and to […]

Continue reading »

BS EN ISO 21078-2:2007 – Determination of boron(III) oxide in refractory products — Part 2: Acid extraction method for the determination of boron(III) oxide in binder components

BS EN ISO 21078-2:2007 - Determination of boron(III) oxide in refractory products — Part 2: Acid extraction method for the determination of boron(III) oxide in binder components

1 Scope This part of ISO 21078 specifies procedures of chemical analysis for the determination of boron(III) oxide used as a binder component added to aluminosilicate refractories, using an acid extraction method. It is applicable for refractories containing less than (mass fraction) of boron(III) oxide. 2 Normative references The following referenced documents are indispensable for the application of this document. […]

Continue reading »

BS EN ISO 15302:2007 – Animal and vegetable fats and oils — Determination of benzo[a]pyrene content — Reverse-phase high-performance liquid chromatography method

BS EN ISO 15302:2007 - Animal and vegetable fats and oils — Determination of benzo[a]pyrene content — Reverse-phase high-performance liquid chromatography method

1 Scope This International Standard specifies a method for the determination of benzo[a]pyrene in crude or refined edible oils and fats by reverse-phase high-performance liquid chromatography (HPLC) using fluorimetric detection in the range from 0,1 µg/kg to 10 µg/kg. 2 Normative reference The following standard contains provisions, which through reference in this text, constitute provisions of this International Standard. At […]

Continue reading »

BS EN ISO 14343:2007 – Welding consumables — Wire electrodes, strip electrodes, wires and rods for fusion welding of stainless and heat resisting steels — Classification

BS EN ISO 14343:2007 - Welding consumables — Wire electrodes, strip electrodes, wires and rods for fusion welding of stainless and heat resisting steels — Classification

1 Scope This International Standard specifies requirements for classification of wire electrodes, wires and rods for gas- shielded metal arc welding, gas tungsten arc welding, plasma arc welding, submerged arc welding and laser beam welding of stainless and heat resisting steels. The classification of the wire electrodes, wires and rods is based upon their chemical composition. This document is a […]

Continue reading »

BS EN ISO 11111-3:2005 – Textile machinery — Safety requirements — Part 3: Nonwoven machinery

BS EN ISO 11111-3:2005 - Textile machinery — Safety requirements — Part 3: Nonwoven machinery

1 Scope This part of ISO 11111 is intended to be used in conjunction with ISO 11111-1, ISO 11111-2, ISO 11111-6 and ISO 11111-7. It specifies significant hazards and corresponding safety requirements and/or measures for nonwoven machinery. By taking into account the scope of ISO 11111-1 as far as is relevant, this part of ISO 11111 is applicable to all […]

Continue reading »

BS EN ISO 10438-3:2007 – Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 3: General-purpose oil systems

BS EN ISO 10438-3:2007 - Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 3: General-purpose oil systems

1 Scope This part of ISO 1 0438, in conjunction with ISO 1 0438-1 , specifies requirements for oil systems for generalpurpose applications. These oil systems can provide lubrication oil, but not seal oil and can serve equipment such as compressors, gears, pumps and drivers. NOTE The term ―general-purpose‖ is defined in ISO 1 0438-1 . 2 Normative references The […]

Continue reading »

BS EN 62300:2005 – Consumer audio/video equipment digital interface with plastic optical fibre

BS EN 62300:2005 - Consumer audio/video equipment digital interface with plastic optical fibre

1 Scope This International Standard specifies the principal electrical and optical parameters for a consumer audio/video equipment digital interface that uses plastic optical fibre (POF). NOTE A description of the principal features of such an interface is given in Annex C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only […]

Continue reading »

BS EN 62271-209:2007 – High-voltage switchgear and controlgear — Part 209: Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV — Fluid-filled and extruded insulation cables — Fluid-filled and dry-type cable- terminations

BS EN 62271-209:2007 - High-voltage switchgear and controlgear — Part 209: Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV — Fluid-filled and extruded insulation cables — Fluid-filled and dry-type cable- terminations

5.3 Rated insulation level The rated insulation level for the cable connection assembly shall be selected from the values given in IEC 60038 (IEC standard voltages) as well as IEC 62271 -203:2003. 5.4 Rated normal current and temperature rise The connection interface of the main circuit shown in Figures 2 and 3 for fluid-filled cable- terminations and Figures 4 and […]

Continue reading »

BS EN 62132-3:2007 – Integrated circuits — Measurement of electromagnetic immunity, 150 kHz to 1 GHz — Part 3: Bulk current injection (BCI) method

BS EN 62132-3:2007 - Integrated circuits — Measurement of electromagnetic immunity, 150 kHz to 1 GHz — Part 3: Bulk current injection (BCI) method

Two electrically shielded magnetic probes are clamped on one wires or a combination of wires that is/are connected to the device under test. The first probe is for the injection of RF power that induces I disturbance onto the wires. The second probe is used for monitoring the i nduced current on those wires. The disturbance current flows in a […]

Continue reading »

BS EN 62056-47:2007 – Electricity metering — Data exchange for meter reading, tariff and load control — Part 47: COSEM transport layers for IPv4 networks

BS EN 62056-47:2007 - Electricity metering — Data exchange for meter reading, tariff and load control — Part 47: COSEM transport layers for IPv4 networks

The Local_wPort, Remote_wPort, Local_UDP_Port, Remote_UDP_Port, Local_IP_Address and Remote_IP_Address parameters carry the same values as the corresponding UDP- DATA.request service being confirmed. The value of the Result parameter indicates whether the COSEM UDP-based transport layer was able to send the requested UDP Datagram (OK) or not (NOK). Use If implemented, this service primitive is used to confirm the result of a […]

Continue reading »
1 23 24 25 26 27 80